lora-irrigation/README.md

LoRa Irrigation System

This project is to build an irrigation system from LoRa capable microcontrollers. The Heltec Node151 was chosen due to it’s small size and inexpensive cost.

Design Decisions

While investigating this, the LoraWAN protocol was investigated, but after looking at the code complexity and other operational requirements, if was decided that for this project, it was safer to target a direct Node to Node style communication system. This would allow the implementation to be more simple, and security to be built in (LoRaWAN does have a crypto layer, BUT, trusting/auditing it and any library that implements it would be a larger task than I want to undertake). It could also be used for other projects that need security.

One of the other requirements is that the code be 100% open sourced, not GPL licensed, and no proprietary components. This meant that using IDE’s like ST’s STM32CubeIDE which is only available in binary form was not a choice, as that would preclude building on an operating system other than Windows/MaxOS/Linux.

Building

The build system uses the BSD flavor of make. This is the default make on the BSDs, originally called pmake, but also available as bsdmake for MacOSX, and available as bmake.

It also depends upon ARM’s GNU Arm Embedded Toolchain, which uses gcc as the compiler. It would be good to get it cross-compile with clang as well, but that requires finding a libc like the nano libc that is provided by the toolchain.

Once ARM’s toolchain is in your path, the following should work:

export MAKEOBJDIR=build
mkdir $MAKEOBJDIR
bsdmake all

And in the directory build, a file lora.irr.elf should be present.

Flashing

Flashing can be done via the open source tool OpenOCD. For this, I use a Digilent HS1 JTAG programmer utilizing the resistor hack to allow an FTDI JTAG programmer to control the bi-directional SWIO pin.

One caveat w/ MacOSX, is that it may be necessary to unload the kext com.apple.driver.AppleUSBFTDI via the command:

sudo kextunload -b com.apple.driver.AppleUSBFTDI

as OpenOCD wants direct access to the FTDI driver.

Once that happens, the device can be programmed using the following command:

sudo openocd -f interface/ftdi/digilent-hs1.cfg -f interface/ftdi/swd-resistor-hack.cfg -f target/stm32l1.cfg -c "init" -c "reset init" -c "program build/lora.irr.elf verify reset exit"

Pins

The pinout guide for the Node151.

The default pins PB5-7,9 are used as active low controls for the relays. They are mapped to channels 0 through 3 respectively. The LED on PB8 is mapped to channel 4. This is useful for testing if a command works or not.

The pin PB15 is used as an analog input for an RNG source. This pin should be grounded.

Deploying

The noral supply used for irrigation values is 24V AC. This means an additional power supply is needed to convert to the 5V supply that is used by the Node151. Make sure this is well filtered as both the relays on the board (talked about below), and the irrigation values will cause significant noise. The first PS I made was a simple DC-DC buck converter + a full wave rectifier which, while alone was enough to power the uC, was not enough when the relays were actuated, and even when a little bit of filtering was added after the rectifier (22uF), enough to keep it happy w/ the relays, it was not enough when the irrigation valves actuated.

In order to control the values, a relay board, similar to this one, can be used. The nice thing about this board is that the GPIO pins on the Node151 are 3.3V, while the relays need 5V to work. The jumper on the right side, VCC-JD-VCC, can be removed to allow this. The GND on the input/VCC pinout is used for the relay power via JD-VCC, and NOT for the VCC->INx pins, despite them being next to each other. The GND and JD-VCC should be connected to the 5V power supply, while VCC is connected to VDD on the Node151, and INx pins to the respective GPIO pins.