/**
  ******************************************************************************
  * @file    stm32l1xx_hal_pwr.h
  * @author  MCD Application Team
  * @brief   Header file of PWR HAL module.
  ******************************************************************************
  * @attention
  *
  * <h2><center>&copy; Copyright (c) 2017 STMicroelectronics.
  * All rights reserved.</center></h2>
  *
  * This software component is licensed by ST under BSD 3-Clause license,
  * the "License"; You may not use this file except in compliance with the
  * License. You may obtain a copy of the License at:
  *                        opensource.org/licenses/BSD-3-Clause
  *
  ******************************************************************************
  */

/* Define to prevent recursive inclusion -------------------------------------*/
#ifndef __STM32L1xx_HAL_PWR_H
#define __STM32L1xx_HAL_PWR_H

#ifdef __cplusplus
 extern "C" {
#endif

/* Includes ------------------------------------------------------------------*/
#include "stm32l1xx_hal_def.h"

/** @addtogroup STM32L1xx_HAL_Driver
  * @{
  */

/** @addtogroup PWR
  * @{
  */

/* Exported types ------------------------------------------------------------*/

/** @defgroup PWR_Exported_Types PWR Exported Types
  * @{
  */

/**
  * @brief  PWR PVD configuration structure definition
  */
typedef struct
{
  uint32_t PVDLevel;   /*!< PVDLevel: Specifies the PVD detection level.
                            This parameter can be a value of @ref PWR_PVD_detection_level */

  uint32_t Mode;      /*!< Mode: Specifies the operating mode for the selected pins.
                           This parameter can be a value of @ref PWR_PVD_Mode */
}PWR_PVDTypeDef;

/**
  * @}
  */

/* Internal constants --------------------------------------------------------*/

/** @addtogroup PWR_Private_Constants
  * @{
  */
#define PWR_EXTI_LINE_PVD  (0x00010000U)  /*!< External interrupt line 16 Connected to the PVD EXTI Line */

/**
  * @}
  */



/* Exported constants --------------------------------------------------------*/

/** @defgroup PWR_Exported_Constants PWR Exported Constants
  * @{
  */

/** @defgroup PWR_register_alias_address PWR Register alias address
  * @{
  */
/* ------------- PWR registers bit address in the alias region ---------------*/
#define PWR_OFFSET               (PWR_BASE - PERIPH_BASE)
#define PWR_CR_OFFSET            0x00
#define PWR_CSR_OFFSET           0x04
#define PWR_CR_OFFSET_BB         (PWR_OFFSET + PWR_CR_OFFSET)
#define PWR_CSR_OFFSET_BB        (PWR_OFFSET + PWR_CSR_OFFSET)
/**
  * @}
  */

/** @defgroup PWR_CR_register_alias PWR CR Register alias address
  * @{
  */
/* --- CR Register ---*/
/* Alias word address of LPSDSR bit */
#define LPSDSR_BIT_NUMBER        POSITION_VAL(PWR_CR_LPSDSR)
#define CR_LPSDSR_BB             ((uint32_t)(PERIPH_BB_BASE + (PWR_CR_OFFSET_BB * 32) + (LPSDSR_BIT_NUMBER * 4)))

/* Alias word address of DBP bit */
#define DBP_BIT_NUMBER           POSITION_VAL(PWR_CR_DBP)
#define CR_DBP_BB                ((uint32_t)(PERIPH_BB_BASE + (PWR_CR_OFFSET_BB * 32) + (DBP_BIT_NUMBER * 4)))

/* Alias word address of LPRUN bit */
#define LPRUN_BIT_NUMBER         POSITION_VAL(PWR_CR_LPRUN)
#define CR_LPRUN_BB              ((uint32_t)(PERIPH_BB_BASE + (PWR_CR_OFFSET_BB * 32) + (LPRUN_BIT_NUMBER * 4)))

/* Alias word address of PVDE bit */
#define PVDE_BIT_NUMBER          POSITION_VAL(PWR_CR_PVDE)
#define CR_PVDE_BB               ((uint32_t)(PERIPH_BB_BASE + (PWR_CR_OFFSET_BB * 32) + (PVDE_BIT_NUMBER * 4)))

/* Alias word address of FWU bit */
#define FWU_BIT_NUMBER           POSITION_VAL(PWR_CR_FWU)
#define CR_FWU_BB                ((uint32_t)(PERIPH_BB_BASE + (PWR_CR_OFFSET_BB * 32) + (FWU_BIT_NUMBER * 4)))

/* Alias word address of ULP bit */
#define ULP_BIT_NUMBER           POSITION_VAL(PWR_CR_ULP)
#define CR_ULP_BB                ((uint32_t)(PERIPH_BB_BASE + (PWR_CR_OFFSET_BB * 32) + (ULP_BIT_NUMBER * 4)))
/**
  * @}
  */

/** @defgroup PWR_CSR_register_alias PWR CSR Register alias address
  * @{
  */

/* --- CSR Register ---*/
/* Alias word address of EWUP1, EWUP2 and EWUP3 bits */
#define CSR_EWUP_BB(VAL)         ((uint32_t)(PERIPH_BB_BASE + (PWR_CSR_OFFSET_BB * 32) + (POSITION_VAL(VAL) * 4)))
/**
  * @}
  */

/** @defgroup PWR_PVD_detection_level PWR PVD detection level
  * @{
  */
#define PWR_PVDLEVEL_0                  PWR_CR_PLS_LEV0
#define PWR_PVDLEVEL_1                  PWR_CR_PLS_LEV1
#define PWR_PVDLEVEL_2                  PWR_CR_PLS_LEV2
#define PWR_PVDLEVEL_3                  PWR_CR_PLS_LEV3
#define PWR_PVDLEVEL_4                  PWR_CR_PLS_LEV4
#define PWR_PVDLEVEL_5                  PWR_CR_PLS_LEV5
#define PWR_PVDLEVEL_6                  PWR_CR_PLS_LEV6
#define PWR_PVDLEVEL_7                  PWR_CR_PLS_LEV7  /* External input analog voltage
                                                            (Compare internally to VREFINT) */

/**
  * @}
  */

/** @defgroup PWR_PVD_Mode PWR PVD Mode
  * @{
  */
#define PWR_PVD_MODE_NORMAL                 (0x00000000U)   /*!< basic mode is used */
#define PWR_PVD_MODE_IT_RISING              (0x00010001U)   /*!< External Interrupt Mode with Rising edge trigger detection */
#define PWR_PVD_MODE_IT_FALLING             (0x00010002U)   /*!< External Interrupt Mode with Falling edge trigger detection */
#define PWR_PVD_MODE_IT_RISING_FALLING      (0x00010003U)   /*!< External Interrupt Mode with Rising/Falling edge trigger detection */
#define PWR_PVD_MODE_EVENT_RISING           (0x00020001U)   /*!< Event Mode with Rising edge trigger detection */
#define PWR_PVD_MODE_EVENT_FALLING          (0x00020002U)   /*!< Event Mode with Falling edge trigger detection */
#define PWR_PVD_MODE_EVENT_RISING_FALLING   (0x00020003U)   /*!< Event Mode with Rising/Falling edge trigger detection */

 /**
 * @}
  */

/** @defgroup PWR_Regulator_state_in_SLEEP_STOP_mode PWR Regulator state in SLEEP/STOP mode
  * @{
  */
#define PWR_MAINREGULATOR_ON           (0x00000000U)
#define PWR_LOWPOWERREGULATOR_ON       PWR_CR_LPSDSR

/**
  * @}
  */

/** @defgroup PWR_SLEEP_mode_entry PWR SLEEP mode entry
  * @{
  */
#define PWR_SLEEPENTRY_WFI             ((uint8_t)0x01)
#define PWR_SLEEPENTRY_WFE             ((uint8_t)0x02)

/**
  * @}
  */

/** @defgroup PWR_STOP_mode_entry PWR STOP mode entry
  * @{
  */
#define PWR_STOPENTRY_WFI              ((uint8_t)0x01)
#define PWR_STOPENTRY_WFE              ((uint8_t)0x02)

/**
  * @}
  */

/** @defgroup PWR_Regulator_Voltage_Scale PWR Regulator Voltage Scale
  * @{
  */

#define PWR_REGULATOR_VOLTAGE_SCALE1       PWR_CR_VOS_0
#define PWR_REGULATOR_VOLTAGE_SCALE2       PWR_CR_VOS_1
#define PWR_REGULATOR_VOLTAGE_SCALE3       PWR_CR_VOS


/**
  * @}
  */

/** @defgroup PWR_Flag PWR Flag
  * @{
  */
#define PWR_FLAG_WU                    PWR_CSR_WUF
#define PWR_FLAG_SB                    PWR_CSR_SBF
#define PWR_FLAG_PVDO                  PWR_CSR_PVDO
#define PWR_FLAG_VREFINTRDY            PWR_CSR_VREFINTRDYF
#define PWR_FLAG_VOS                   PWR_CSR_VOSF
#define PWR_FLAG_REGLP                 PWR_CSR_REGLPF

/**
  * @}
  */

/**
  * @}
  */

/* Exported macro ------------------------------------------------------------*/
/** @defgroup PWR_Exported_Macros PWR Exported Macros
  * @{
  */

/** @brief  macros configure the main internal regulator output voltage.
  * @param  __REGULATOR__ specifies the regulator output voltage to achieve
  *         a tradeoff between performance and power consumption when the device does
  *         not operate at the maximum frequency (refer to the datasheets for more details).
  *          This parameter can be one of the following values:
  *            @arg PWR_REGULATOR_VOLTAGE_SCALE1: Regulator voltage output Scale 1 mode,
  *                                                System frequency up to 32 MHz.
  *            @arg PWR_REGULATOR_VOLTAGE_SCALE2: Regulator voltage output Scale 2 mode,
  *                                                System frequency up to 16 MHz.
  *            @arg PWR_REGULATOR_VOLTAGE_SCALE3: Regulator voltage output Scale 3 mode,
  *                                                System frequency up to 4.2 MHz
  * @retval None
  */
#define __HAL_PWR_VOLTAGESCALING_CONFIG(__REGULATOR__) (MODIFY_REG(PWR->CR, PWR_CR_VOS, (__REGULATOR__)))

/** @brief  Check PWR flag is set or not.
  * @param  __FLAG__ specifies the flag to check.
  *           This parameter can be one of the following values:
  *            @arg PWR_FLAG_WU: Wake Up flag. This flag indicates that a wakeup event
  *                  was received from the WKUP pin or from the RTC alarm (Alarm B),
  *                  RTC Tamper event, RTC TimeStamp event or RTC Wakeup.
  *                  An additional wakeup event is detected if the WKUP pin is enabled
  *                  (by setting the EWUP bit) when the WKUP pin level is already high.
  *            @arg PWR_FLAG_SB: StandBy flag. This flag indicates that the system was
  *                  resumed from StandBy mode.
  *            @arg PWR_FLAG_PVDO: PVD Output. This flag is valid only if PVD is enabled
  *                  by the HAL_PWR_EnablePVD() function. The PVD is stopped by Standby mode
  *                  For this reason, this bit is equal to 0 after Standby or reset
  *                  until the PVDE bit is set.
  *            @arg PWR_FLAG_VREFINTRDY: Internal voltage reference (VREFINT) ready flag.
  *                 This bit indicates the state of the internal voltage reference, VREFINT.
  *            @arg PWR_FLAG_VOS: Voltage Scaling select flag. A delay is required for
  *                 the internal regulator to be ready after the voltage range is changed.
  *                 The VOSF bit indicates that the regulator has reached the voltage level
  *                 defined with bits VOS of PWR_CR register.
  *            @arg PWR_FLAG_REGLP: Regulator LP flag. When the MCU exits from Low power run
  *                 mode, this bit stays at 1 until the regulator is ready in main mode.
  *                 A polling on this bit is recommended to wait for the regulator main mode.
  *                 This bit is reset by hardware when the regulator is ready.
  * @retval The new state of __FLAG__ (TRUE or FALSE).
  */
#define __HAL_PWR_GET_FLAG(__FLAG__) ((PWR->CSR & (__FLAG__)) == (__FLAG__))

/** @brief  Clear the PWR's pending flags.
  * @param  __FLAG__ specifies the flag to clear.
  *          This parameter can be one of the following values:
  *            @arg PWR_FLAG_WU: Wake Up flag
  *            @arg PWR_FLAG_SB: StandBy flag
  */
#define __HAL_PWR_CLEAR_FLAG(__FLAG__) SET_BIT(PWR->CR, ((__FLAG__) << 2))

/**
  * @brief Enable interrupt on PVD Exti Line 16.
  * @retval None.
  */
#define __HAL_PWR_PVD_EXTI_ENABLE_IT()      SET_BIT(EXTI->IMR, PWR_EXTI_LINE_PVD)

/**
  * @brief Disable interrupt on PVD Exti Line 16.
  * @retval None.
  */
#define __HAL_PWR_PVD_EXTI_DISABLE_IT()     CLEAR_BIT(EXTI->IMR, PWR_EXTI_LINE_PVD)

/**
  * @brief Enable event on PVD Exti Line 16.
  * @retval None.
  */
#define __HAL_PWR_PVD_EXTI_ENABLE_EVENT()   SET_BIT(EXTI->EMR, PWR_EXTI_LINE_PVD)

/**
  * @brief Disable event on PVD Exti Line 16.
  * @retval None.
  */
#define __HAL_PWR_PVD_EXTI_DISABLE_EVENT()  CLEAR_BIT(EXTI->EMR, PWR_EXTI_LINE_PVD)


/**
  * @brief  PVD EXTI line configuration: set falling edge trigger.
  * @retval None.
  */
#define __HAL_PWR_PVD_EXTI_ENABLE_FALLING_EDGE()  SET_BIT(EXTI->FTSR, PWR_EXTI_LINE_PVD)


/**
  * @brief Disable the PVD Extended Interrupt Falling Trigger.
  * @retval None.
  */
#define __HAL_PWR_PVD_EXTI_DISABLE_FALLING_EDGE()  CLEAR_BIT(EXTI->FTSR, PWR_EXTI_LINE_PVD)


/**
  * @brief  PVD EXTI line configuration: set rising edge trigger.
  * @retval None.
  */
#define __HAL_PWR_PVD_EXTI_ENABLE_RISING_EDGE()   SET_BIT(EXTI->RTSR, PWR_EXTI_LINE_PVD)

/**
  * @brief Disable the PVD Extended Interrupt Rising Trigger.
  * @retval None.
  */
#define __HAL_PWR_PVD_EXTI_DISABLE_RISING_EDGE()  CLEAR_BIT(EXTI->RTSR, PWR_EXTI_LINE_PVD)

/**
  * @brief  PVD EXTI line configuration: set rising & falling edge trigger.
  * @retval None.
  */
#define __HAL_PWR_PVD_EXTI_ENABLE_RISING_FALLING_EDGE()  \
  do {                                                   \
    __HAL_PWR_PVD_EXTI_ENABLE_RISING_EDGE();             \
    __HAL_PWR_PVD_EXTI_ENABLE_FALLING_EDGE();            \
  } while(0)

/**
  * @brief Disable the PVD Extended Interrupt Rising & Falling Trigger.
  * @retval None.
  */
#define __HAL_PWR_PVD_EXTI_DISABLE_RISING_FALLING_EDGE()  \
  do {                                                    \
    __HAL_PWR_PVD_EXTI_DISABLE_RISING_EDGE();             \
    __HAL_PWR_PVD_EXTI_DISABLE_FALLING_EDGE();            \
  } while(0)



/**
  * @brief Check whether the specified PVD EXTI interrupt flag is set or not.
  * @retval EXTI PVD Line Status.
  */
#define __HAL_PWR_PVD_EXTI_GET_FLAG()       (EXTI->PR & (PWR_EXTI_LINE_PVD))

/**
  * @brief Clear the PVD EXTI flag.
  * @retval None.
  */
#define __HAL_PWR_PVD_EXTI_CLEAR_FLAG()     (EXTI->PR = (PWR_EXTI_LINE_PVD))

/**
  * @brief Generate a Software interrupt on selected EXTI line.
  * @retval None.
  */
#define __HAL_PWR_PVD_EXTI_GENERATE_SWIT()  SET_BIT(EXTI->SWIER, PWR_EXTI_LINE_PVD)

/**
  * @}
  */

/* Private macro -------------------------------------------------------------*/
/** @defgroup PWR_Private_Macros PWR Private Macros
  * @{
  */

#define IS_PWR_PVD_LEVEL(LEVEL) (((LEVEL) == PWR_PVDLEVEL_0) || ((LEVEL) == PWR_PVDLEVEL_1)|| \
                                 ((LEVEL) == PWR_PVDLEVEL_2) || ((LEVEL) == PWR_PVDLEVEL_3)|| \
                                 ((LEVEL) == PWR_PVDLEVEL_4) || ((LEVEL) == PWR_PVDLEVEL_5)|| \
                                 ((LEVEL) == PWR_PVDLEVEL_6) || ((LEVEL) == PWR_PVDLEVEL_7))


#define IS_PWR_PVD_MODE(MODE) (((MODE) == PWR_PVD_MODE_IT_RISING)|| ((MODE) == PWR_PVD_MODE_IT_FALLING) || \
                              ((MODE) == PWR_PVD_MODE_IT_RISING_FALLING) || ((MODE) == PWR_PVD_MODE_EVENT_RISING) || \
                              ((MODE) == PWR_PVD_MODE_EVENT_FALLING) || ((MODE) == PWR_PVD_MODE_EVENT_RISING_FALLING) || \
                              ((MODE) == PWR_PVD_MODE_NORMAL))

#define IS_PWR_REGULATOR(REGULATOR) (((REGULATOR) == PWR_MAINREGULATOR_ON) || \
                                     ((REGULATOR) == PWR_LOWPOWERREGULATOR_ON))


#define IS_PWR_SLEEP_ENTRY(ENTRY) (((ENTRY) == PWR_SLEEPENTRY_WFI) || ((ENTRY) == PWR_SLEEPENTRY_WFE))

#define IS_PWR_STOP_ENTRY(ENTRY) (((ENTRY) == PWR_STOPENTRY_WFI) || ((ENTRY) == PWR_STOPENTRY_WFE) )

#define IS_PWR_VOLTAGE_SCALING_RANGE(RANGE) (((RANGE) == PWR_REGULATOR_VOLTAGE_SCALE1) || \
                                             ((RANGE) == PWR_REGULATOR_VOLTAGE_SCALE2) || \
                                             ((RANGE) == PWR_REGULATOR_VOLTAGE_SCALE3))


/**
  * @}
  */



/* Include PWR HAL Extension module */
#include "stm32l1xx_hal_pwr_ex.h"

/* Exported functions --------------------------------------------------------*/

/** @addtogroup PWR_Exported_Functions PWR Exported Functions
  * @{
  */

/** @addtogroup PWR_Exported_Functions_Group1 Initialization and de-initialization functions
  * @{
  */

/* Initialization and de-initialization functions *******************************/
void HAL_PWR_DeInit(void);
void HAL_PWR_EnableBkUpAccess(void);
void HAL_PWR_DisableBkUpAccess(void);

/**
  * @}
  */

/** @addtogroup PWR_Exported_Functions_Group2 Peripheral Control functions
  * @{
  */

/* Peripheral Control functions  ************************************************/
void HAL_PWR_ConfigPVD(PWR_PVDTypeDef *sConfigPVD);
void HAL_PWR_EnablePVD(void);
void HAL_PWR_DisablePVD(void);

/* WakeUp pins configuration functions ****************************************/
void HAL_PWR_EnableWakeUpPin(uint32_t WakeUpPinx);
void HAL_PWR_DisableWakeUpPin(uint32_t WakeUpPinx);

/* Low Power modes configuration functions ************************************/
void HAL_PWR_EnterSTOPMode(uint32_t Regulator, uint8_t STOPEntry);
void HAL_PWR_EnterSLEEPMode(uint32_t Regulator, uint8_t SLEEPEntry);
void HAL_PWR_EnterSTANDBYMode(void);

void HAL_PWR_EnableSleepOnExit(void);
void HAL_PWR_DisableSleepOnExit(void);
void HAL_PWR_EnableSEVOnPend(void);
void HAL_PWR_DisableSEVOnPend(void);



void HAL_PWR_PVD_IRQHandler(void);
void HAL_PWR_PVDCallback(void);
/**
  * @}
  */

/**
  * @}
  */

/**
  * @}
  */

/**
  * @}
  */

#ifdef __cplusplus
}
#endif


#endif /* __STM32L1xx_HAL_PWR_H */

/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/